#!/usr/bin/env bash
#=============================================================================
# Copyright 2018 Kitware, Inc.
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#=============================================================================

# Run this script to set up the Girder API keys. This is used by the
# Utilities/UploadBinaryData.sh script to perform authenticated uploads of
# binary testing data.

die() {
	echo 1>&2 "$@" ; exit 1
}

json_field() {
  local key=$1
  local json=$2
  echo $json | awk 'BEGIN { FS="\""; RS="," }; { if ($2 == "'$key'") {print $4} }'
}


# Make sure we are inside the repository.
cd "${BASH_SOURCE%/*}" &&

protocol=$(git config -f config --get girder.protocol || echo "https") &&
host=$(git config -f config --get girder.host || echo "data.kitware.com") &&
site=$(git config -f config --get girder.site || echo "$protocol://$host")

api_key=$(git config --get girder.api-key || echo '')

# Tell user about current configuration.
if test -n "$api_key"; then
	echo 'The Girder API key is currently set to "'"${api_key:0:5}"'..."' &&
	read -ep 'Reconfigure Girder API key? [y/N]: ' ans &&
	if [ "$ans" == "y" ] || [ "$ans" == "Y" ]; then
		setup=1
	else
		setup=''
	fi
else
	echo 'A Girder API key is not configured to upload testing data.
' &&
	read -ep 'Configure Git to contribute testing data to '"$host"'? [Y/n]: ' ans &&
	if [ "$ans" == "n" ] || [ "$ans" == "N" ]; then
		exit 0
	else
		setup=1
	fi
fi &&

setup_instructions='Once registered, login to Girder at

  '"$site/#?dialog=login"'

Then visit

  <username> (upper right) > My account > API keys > Create new key

To create a new API key.
'

# Perform setup if necessary.
if test -n "$setup"; then
	echo 'Register for an account at

  '"$site/#?dialog=register"'

'"$setup_instructions" &&
	read -ep "Girder API key?: " gak &&
	git config girder.api-key "$gak" &&
        api_key=$(git config --get girder.api-key) &&
	echo 'The Girder API key is now configured to

  '"${api_key:0:5}..."'
'
fi &&

# Optionally test GitHub access.
if test -n "$api_key"; then
  read -ep 'Test access to Girder via API key? [y/N]: ' ans &&
  if [ "$ans" == "y" ] || [ "$ans" == "Y" ]; then
    echo -n 'Testing Girder access via API key...'
    token=""
    token_response=$(curl -s -X POST --header 'Content-Length: 0' --header 'Content-Type: application/json' --header 'Accept: application/json' "https://data.kitware.com/api/v1/api_key/token?key=${api_key}&duration=1" || die "Could not retrieve token from API key.")
    token=$(json_field "token" "${token_response}")
    if test -z "$token"; then
      echo 'failed.' &&
      die 'Could not access Girder via your API key.'
    else
      echo 'passed.'
    fi
  fi
fi